Category: 

How Is a Jointer Used in Woodworking?

Article Details
  • Written By: L. S. Wynn
  • Edited By: L. S. Wynn
  • Last Modified Date: 22 March 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
There has never been a documented human death associated with a tarantula bite.  more...

April 19 ,  1775 :  The American Revolution began.  more...

Wood is a beautiful material that is relatively easy to work with and has some amazing properties. One of the disadvantages to wood, however, is that it expands, contracts, cups, and warps in different conditions, so it is not as stable as stone or most metals. To begin a project, a woodworker usually starts with rough lumber and must go through various steps to ensure that it is flat. Some woodworkers prefer to use handtools only, but for those that use power tools, a jointer is typically used.

The majority of warping and splitting of wood occurs after it is cut out of the log and dried. Each board will continue to move throughout its life as the temperature and humidity changes. When a woodworker purchases wood from a lumberyard, it is rarely flat and smooth and special tools are required to prepare it for use in projects such as furniture.

A jointer includes infeed and outfeed tables, and a set of rotating blades is positioned between these two tables. A fence is set on one side to serve as a guide. The infeed table and outfeed table are adjusted so that they are close to parallel, but the infeed is slightly lower, exposing a small amount of the cutting blades. The woodworker presses the lumber against the infeed table and pushes it onto the outfeed table; the rapidly spinning blades remove a small amount of material. If the wood is particularly warped, several passes may be required.

Ad

After a sufficient number of passes, one surface of the wood is flat. The process usually continues with a thickness planer, another specialized power tool that removes wood from the opposite face of the board. A few passes through a thickness planer creates a board that has two flat and parallel face.

Next, the woodworker usually takes the partially surfaced board back to the jointer to square up the edge. In this instance, the board is placed vertically against the fence. A few passes may be required to get a flat edge that is square to the two faces. The remaining edge is usually squared up on a table saw.

The fence on most machines can be adjusted to various angles. By adjusting the fence in this way, the device can also be used to create chamfers along the edge of a board.

how is a jointer used in woodworking

Ad

Discuss this Article

anon222999
Post 9

I'm doing a school project about the safety procedures and how a jointer works And I don't know anything about a jointer. Can anyone help?

anon53917
Post 7

When I use my jointer it gives me a concave edge. Any ideas to fix this problem?

anon52309
Post 6

The outfeed table should be level with the top of the cutter head. The cutter head should be no more than 1/8" higher than the infeed table, but I would only recommend about 1/16" or less, unless you have an extremely powerful jointer.

anon37772
Post 5

Why do I get a low spot at the end of my cut.

What do I need to know about safety using a 6" Powermatic model 50 jointer. Why do I get bumps on my cut of a 4x4 oak board.

edgedown
Post 4

Will a jointer function well on an end grain surface?

thanks

anon23446
Post 3

Yes..This is the proper way to square up stock if (big IF) the tools mentioned are calibrated and have true edges themselves...it's why good cabinet quality tools are pricey.

anon14745
Post 2

Thanks for the directions. I, being a rookie woodworker, had them backwards. Jack

anon4940
Post 1

how many blades are on the jointer cutter?

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email