Category: 

What Are Brake Pads?

Brake pads take the blunt of the force needed to stop a moving vehicle.
New brake pads can be replaced in a few hours with the proper tools.
Kevlar® fabric, which is used to make brake pads.
Brake pads can easily be changed with the use of a simple car jack.
Most brake pads sold today are considered semi-metallic.
Article Details
  • Written By: Michael Pollick
  • Edited By: Niki Foster
  • Last Modified Date: 13 October 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
As of 2014, the world’s most expensive divorce cost a Russian oligarch $4.5 billion USD.  more...

October 19 ,  1987 :  The Dow Jones experienced its second-largest percentage drop in history.  more...

Brake pads are the parts of a car's braking system that actually take the brunt of the frictional force necessary to stop the car. In a disc brake system, the brake pedal activates a hydraulic line which squeezes the calipers against the rotors of the car's tires. Pads are positioned between the calipers and the rotors to absorb the energy and heat, then provide enough grip to stop the car.

A good analogy for understanding disc brakes is a ten speed bicycle. The handgrip under the rider's hand is like the brake pedal of a car. As the rider squeezes this grip, cables pull two hinged pieces called calipers together. The calipers themselves do not contact the rim of the tire, but two rubber pieces do. These rubber shoes work much like automotive brake pads. The metallic rim of the tire is essentially a rotor. The friction between the pads and rotor is the key to stopping in a disc brake system. Eventually, however, the rubber shoes of a bicycle and the brake pads of a car will wear down and severely compromise the operator's safety.

Brake pads were originally made with organic ingredients such as asbestos and carbon, held together by a strong resin. The use of asbestos was eventually banned by the US government, but some non-metallic or organic versions are still sold. Only vehicles designed for organic pads can use them, however. The same material used in bulletproof vests, Kevlar®, has replaced asbestos in non-metallic brake pads.

Ad

Most brake pads sold today are considered semi-metallic. Manufacturers often guard their actual formulas, but in general these use copper, brass, and steel wool shavings held together in a resin. Because they are primarily metallic, they can last for thousands of miles. Their main drawback for drivers is a higher incidence of grinding noises. This is largely unavoidable, since the metal shavings must rub against steel rotors every time the brakes are applied. Some after-market versions are marketed as quieter than the standard semi-metallic brands.

Brake pads often have special shims built into them to deliberately create a grinding noise as they wear out, in order to alert drivers to have them replaced as soon as possible. If the pads continue to grind, the exposed metal of the caliper may carve out a channel in the rotor. If such damage occurs, the entire rotor must either be replaced or turned. Mechanics can shave off a thin layer of metal from the rotor to remove minor grooves. Since new rotors are relatively inexpensive, however, many mechanics recommend replacing them entirely. New brake pads can be replaced in a few hours if the owner has the tools and patience to perform the job. It is important to apply a special lubricating grease between the new pads and the calipers to avoid a hideous grinding noise. Calipers may also have to be readjusted to accommodate the thickness of new pads.

Ad

More from Wisegeek

You might also Like

Discuss this Article

PelesTears
Post 3

@ Anon4155- If you search youtube you will be able to find a number of instructional videos on changing brake pads. The procedure is simple, varying only slightly from vehicle to vehicle.

I have done brake work on numerous vehicles and my best advice is to:

1) Borrow a Hanes or Chilton's repair manual from your local library

2) Read the instructions

3) Then watch the video before doing brakes for the first time.

Make sure you have all of the parts, tools, and time you will need to complete the job.

If you run into trouble, the person at your local auto parts shop can usually give you advice on whatever has you stuck. Good luck, and have fun learning how to do a job a shop would charge you hundreds for at a fraction of the cost.

anon4155
Post 2

Hi, your article is nice & informative; however you include a link to automedia.com for instructions on "how to replace your brake pads" - but I have been all over that site and it does not give that information. I haven't been able to locate a site that will give step by step instructions. maybe I am not looking hard enough, but I don't see why it takes all of this to retrieve the information I need from the web. Please refer us to a better site. Thanks so much!!

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email