Category: 

What are Cinder Blocks?

Cinder blocks are hollow masonry blocks.
A cinder block wall.
Article Details
  • Written By: Michael Pollick
  • Edited By: Bronwyn Harris
  • Last Modified Date: 14 October 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
The fewest car accident fatalities occur on Tuesdays.  more...

October 23 ,  1983 :  Suicide bombers killed nearly 300 US and French military troops in Beirut.  more...

Some construction projects call for a larger masonry block than a standard brick, but solid concrete blocks can be very expensive and very heavy. One common compromise are largely hollow masonry blocks known as cinder blocks. These are also sometimes referred to as concrete blocks, breeze blocks, or concrete masonry units (CMUs), though these terms have nuanced differences among them. Cinder blocks are generally lighter than solid concrete blocks, which makes them easier for brick masons to place in position. The hollow spaces in the blocks also provide some natural insulation or allow grout to be poured inside the rows of masonry.

Cinder blocks differ from concrete blocks in other ways besides their hollow design. Concrete blocks are made from a slurry of Portland cement and small aggregate, such as small stones or gravel. This makes them heavier and smoother than cinder blocks, which are made from a combination of Portland cement and cinders, the dusty remnants of burned coal.

When bricklayers work with cinder blocks, they generally use techniques similar to standard brick laying. The alternative rows of blocks are carefully offset so that the second layer stabilizes the first. A line of mortar is put down between each layer, so the actual dimensions of a standard cinder block may be adjusted slightly to accommodate the mortar. Corners may be finished out with half blocks, or interlaced to create a four-cornered structure.

Ad

Because cinder blocks do not have a significant amount of tensile strength, concrete is often poured vertically into the hollow chambers to provide more stability and strength. An metal rod called rebar is often placed vertically in the hollow chambers as well to reinforce the poured grout and the wall in general. It is not unusual to see rows of blocks with lengths of exposed rebar on construction sites.

The problem with using grout with standard cinder blocks is block placement. The blocks must be carefully threaded over the rebar before they can be put into place. This may not be a problem for shorter projects such as home foundations, but it would be difficult and time consuming to thread individual blocks over 20 feet sections of rebar. There is a solution to this problem, however. Some cinder blocks, called speed blocks in the construction industry, are open-ended, generally shaped like the letter H. These speed blocks can be maneuvered around existing rebar and tilted into place by a skilled bricklayer.

Ad

More from Wisegeek

You might also Like

Discuss this Article

anon268242
Post 16

I want to install a hinged television bracket. What are the risks and what are the precautions I can take?

The bracket is quite heavy.

anon256886
Post 15

This is an answer for anon148112. For a 4 feet by 40 feet, the first run is 42 blocks, counting for corners. Multiply that by however many blocks high you're going to go. You will end up with extra blocks, but this is a good thing, because it's much better than getting halfway into your project and finding faulty cinder blocks that cannot be used. Therefore, you will have enough to finish your project.

Most places like Home Depot and Lowes will allow for a return on the blocks that were not used for a refund. This is a measurement for cinder/concrete blocks, a.k.a "breeze" blocks, and make sure at least eight of those blocks are corner blocks. If you end up with more corner blocks than planned, no worries. These can be used in straight runs with a slight increase of mortar application, and make sure to keep your mortar mix consistent to allow for "settling" of the blocks.

anon148112
Post 13

How many cinder blocks are needed to build a wall 4' x 40'?

anon136905
Post 12

I was told that cinder blocks float in water and do not sink. Is this true?

anon117413
Post 11

How old is cinder block technology?

anon110150
Post 10

The white stuff is called efflorescence. It can be cleaned off with a weak acid solution. Read up on the process and be careful as most folks use hydrocloric acid.

If your cabinets are hanging on a cinder wall you shouldn't have a problem so long as you use proper wall anchors (not nails). An expanding anchor should do the trick.

shore
Post 9

My basement cinder blocks are bleeding a white color. what is it?

anon91697
Post 8

i like cinder stone a lot because i have my kitchen constructed on cinder stone.

anon73030
Post 6

our cinder blocks are bleeding a white color, almost like a stain, could someone tell me what it is. thanks

anon71864
Post 2

quality wood construction is actually lighter than melamine or particle man made substitutes. Newer refrigerators are way lighter than the old ones from the 70'2 and 80's. Don't you have a refrigerator in your kitchen now? Most of today's products are lighter in weight, because it is all cheap stuff compared to the old products they replaced.

anon62350
Post 1

Our kitchen is constructed on cinder blocks and I want to add to the cupboards but am cautious about the extra weight on the cinder blocks. The new cupboards will be wood, and the existing cupboards are melamine, plus a fridge. Anyone's opinion would be appreciated.

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email