Category: 

What is an Engine Flush?

A new engine with low mileage may need an engine flush if the oil has not been changed regularly.
An older engine with a buildup of sludge may not warrant an engine flush.
Article Details
  • Written By: Malcolm Tatum
  • Edited By: Bronwyn Harris
  • Last Modified Date: 13 April 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
Fluorescent light bulbs use 80% less electricity and last as much as 12 times longer than conventional light bulbs.  more...

April 16 ,  1947 :  The term "Cold War" w  more...

Engine flushing is a procedure that is used to clean the engine of sludge and other elements that build up in various parts of the machinery over time. The main purpose of this procedure is to prolong the life of the engine. By flushing an engine periodically, the internal components of the engine remain relatively clean and thus perform at optimum levels.

The process employed to flush an engine is somewhat similar to transmission flushing. With a transmission flush, the usual flow of fluid through the mechanism is used to push old fluid and various contaminants out of the system via the drain plug. With an engine flush, the cleansing chemicals are introduced and allowed to circulate through the engine, following the same flow pattern as the oil that lubricates the engine components. The chemicals eventually make their way to the oil pan, where the chemicals and the sludge they have removed deposit.

Ad

While in theory the engine flush seems like a task that should be performed from time to time, not everyone agrees that the flush is effective. While it is generally acknowledged that this process is helpful in low mileage vehicles that have not had the oil changed as often as recommended, some professional mechanics question the effectiveness of the flush with high mileage vehicles. The idea is that the buildup of sludge and deposits in the older engine may be more than the chemicals in the flush can process, resulting in making a bad situation worse. Instead of using an engine flush, they recommend that the engine be dismantled and the components thoroughly cleaned, assuming the engine is still in working order.

Because of the difference of opinion among professionals regarding the effectiveness of an engine flush, not every garage or automotive center will offer this service. Even among the mechanics who do offer engine flushes will generally evaluate the condition of the engine before recommending the procedure.

It is important to note that an engine flush is not a substitute for using the proper weight and grade of oil, or having the oil changed according to manufacturer recommendations. At best, it should be considered a way to augment proper maintenance and thus help to prolong the life of the engine.

Ad

Discuss this Article

anon930071
Post 8

I have a 2006 330i. In July 2013, I had the vehicle serviced for a cooling system flush, because I received an email reminder to have it done to prevent future cooling system failures.

My question is now, almost seven months later and (how conveniently) there's a leaking lower radiator hose, the coolant temp sensor needs replacing, and the thermostat and water pump need replacing. Is this even remotely possible to have all fail at the same time and how come this wasn't known six months ago when the system was just serviced?

anon331551
Post 7

I see a lot of hate for engine flushes on the internet. It's kind of like buying anything, really. If you don't put the research in, and just buy what they sell at the grocery store, you're more than likely going to end up with something that isn't going to be the best for your motor. However, you also have Pro-Tec Autocare which was engineered for mechanics to use during routine maintenance and servicing. This engine flush is certified by the super strict German Technical Inspection Agency and provides superior lubrication during the engine flush procedure. It will increase the old oils lubrication by almost 90 percent during the flush so their is no cause for concern on lower end bearings. We've tried seafoam as they have been around forever, but it doesn't even stack up when compared to Protec.

anon236659
Post 4

I was charged 850 for 20 k service of swift vdi. Is it reasonable or just like that?

anon229809
Post 3

Having an engine flush done under pressure through the oil cooler lines is a very effective service to help eliminate valve train deposits from affecting components such as vvt, and valve stem seals. Pouring in a can of flush and running your engine is not only a waste of time, but can be damaging to lower end bearings. Flushes should be done by a professional with proper equipment, not some dumb backyard fix like using a quart of trans fluid or diesel.

anon122496
Post 2

i believe an engine flush killed my engine. i read an article stating it actually does more harm than good. they were right.

anon47500
Post 1

There seem to be different "forms" of engine flushes. There are high-speed/pressurized systems that "flush" out the engine, not exactly sure how. Then we have other techniques such as emptying one quart of oil from the crankcase, add 1 quart of kerosene, and then let the engine idle for 5-10 minutes. Then another similar, is the "seafoam" treatment, in which you add 1 fl. oz. of "seafoam engine treatment" per every quart of oil your crankcase holds; drive the car safely (don't hammer on the gas pedal, or doing any sporadic driving out of the norm) drive the vehicle to your oil change location, and get your lube oil and filter change done, with the vehicle as hot as possible. Keep the engine idled in the parking lot until they can service you. The Seafoam (which is a 100 percent petroleum product), IPA, and some other cleaning agents works by cleaning up the internals of the engine, which is less harsh than these "pressurized" systems that some of these quick lube places perform. So anyway, get the oil changed, and after it's done, I always like to look under the hood, check the oil levels, and make sure everything is to spec, and then add more seafoam (this is post-oil change), same as the pre-oil change, one oz. of seafoam per every quart of oil. Every gasoline fill up, you want to monitor the level and color of your oil (which is why I also mentioned to check the color after the oil change, while in their parking lot). When the oil gets dark, it's time to change it. But, don't drive anymore than 3000 miles on this "seafoamed" oil. Depending on how much sludge you had built up, you may not even experience black oil at the dipstick, but don't go anymore than 3000 miles on this oil. After this, just get the lube, oil, filter, changed as normal. Perhaps upgrade to a synthetic, or even a synthetic blend for added protection and engine longevity (some oil advertisements even claim an increase in MPG using synthetic. who knows, though). Seafoam is s straight 100 percent petroleum product, but also contains other additives to help clean out your crankcase and other "innards". So it won't "thin out" your oil at all. The thing you've got to be careful for, is older engines, or those with excess sludge, having that sludge get freed up, it's no good driving on sludged up/softened oil. Which is why I recommend the initial "flush" then the second/post "treatment" to soak up the remaining sludge that may be left behind. Last of all? Don't skimp on your oil. Demand the best, do your own research on oil and get the best for your vehicle, if you want your vehicle to last.

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email